I have a bed that looks like this, doesn’t have legs.
I was looking at bed risers, but they’re aimed for beds with legs. Also, the risers make the bed rise too high for my needs.
I only need to make the bed rise for about 2-inches so I can use an overbed table like
.
8 hockey pucks
Damn, that’s a great simple idea for cheap.
Well done.
If I see something that needs to be 1in higher my first thought is, “I should put a hockey puck under that.”
Once in college I had a friend who was tired of having a bed that was too low. He used 8 crates of beer, with empty bottles still inside of course.
¯\_(ツ)_/¯
You could set the bed on top of pieces of 4"x4" lumber
Put some screws in it to prevent it from slipping and you’ve got yourself a bed on legs
If the bed is only supported with compressed sawdust lumber, reducing the load points would lead to failure.
To get that thing under the platform, you’re going to need to add stubby legs like the ones on a stuffed chair, unless you want it to look like a dorm room with sticks or bricks. At a guess, I’d say you’ll need 1 leg for every 2-3 linear feet that the bed contacts the ground. Don’t forget the center support.
Platform beds aren’t designed to have legs, so you’ll need significantly more legs than a framed bed would have. You’ve got to spread the additional stresses evenly or it’ll all loosen. It’ll start creaking and the drawers will get stuck with too few supports.
Personally, I would rest it on some sawed-off pieces of a 2x4, but that’s just me. It’d probably be a little ugly.
Something like a few red bricks would probably look a little nicer.
If the 2x4 width (about 1.5) is too small, 2x3 lumber is common. Get a bunch and screw two boards together to use three 3 inch (actually about 2.5) so that you don’t worry about the board tipping.
Since your current frame is legless, i’d probably do a decent sized frame underneath so not just supported at corners.
The big question that prevents the best answer from being obvious is how the existing bed frame is constructed.
If the material is a compressed sawdust wood and that is the material supporting the entire load, like Ikea stuff, then you shouldn’t reduce the contact area with the floor too much. Simply notching the frame with a gentle radius in the area you need the legs to go under the bed would work, the smaller the amount of material removed, the better. So two half circles would be better than one 24" long rectangle with radiused corners. That could be done with a rotary tool or a fretsaw if you don’t have more appropriate tools to minimize tear-out. You would want to cover the cuts with some veneer to prevent the legs from eroding the frame.
Multiple bricks spaced around the perimeter.
Already commented about raising the bed. Here’s another idea.
Remove the top of the desk from the bottom and rotate it 180°, then reinsert. Put a heavy weight on the foot to stabilize, then cantelever the desk out over the bed.
Put books under it.
2 X bed lengths of 2x2, 2 X bed widths of 2x2. Lay them underneath the edges, preferably glued
Really simple idea that’s difficult to put into words easily but handy folk will know what I mean
They should not do this without checking where the bed is supported on the floor. Your method only lifts the perimeter of the bed. It is very likely that the bed also rests on the floor down the center line of the bed or at other spots within the perimeter. If they only prop up the perimeter of the bed, it is liable to collapse in the center.
Telepathic Levitation is your friend.
Probably be easier to remove 2 inches from the table. Take to a welder and have them cut a chunk out of the middle.
I don’t think it’s the height of the table, it’s that it needs to roll under the bed.
I think the issue is that the base is supposed to be able to go under the bed to bring the table part over the bed.
The legs of the table need to go under the bed.
Currently there’s zero space under the bed, that’s why I need something similar to a riser.
Oh the ones at hospitals swivel around so they can go next to things.
That table telescopes. Looks like it already has a way to adjust?
In any case, you could also add feet to the bed. I’d drop examples, except without knowing more about how the bed is made, the specifics get a bit wonky
Another option is taking a couple 4x4’s and trimming them down to the right height and setting them out in a frame- bed on top. (2x4’s are not quite 2”, but if those are thick enough, even simpler,)
Can you not use one designed for your lap? https://www.amazon.com/LapGear-Office-Device-Ledge-Holder/dp/B089P33W98/
never seen this cushion design, I’ll think about it.
That might cause some neck strain because it sits too low. OP’s table is great for working in bed because you can raise your laptop to eye level.
That’s a great point. I never used mine for than an hour at a time
For this purpose, I’d recommend something more like this: Laptop Desk Folding Bed Tray
That will sit on the bed, instead of under it, but will raise the surface up to whatever height is needed.
I know people are saying like bricks and wood and stuff, but if you don’t care how it looks, reams of paper are cheap and customizable, and even stable if you keep them in the plastic wrap and just slide out what you don’t need
I’d just cut the frame to fit the table under it.
Does the bed have sliders under the corners? I’d look for that first to see if it’s designed to be either truly held up by the length of the beams or if it’s actually already supported by the corners. If it’s just the corners, then you only need risers at the corner. If it’s making full contact with the floor, I’d prefer to continue supporting it almost fully with longer beams, leaving a gap where this stand goes
